With a traditional fireplace inside your house, you’ll sometimes notice that the fireplace doesn’t bring enough heat to keep you comfortable on a chilly day. You may improve your condition if your fireplace has a damper, which is just a chimney baffle, by shutting it a little to hold some of the hot gasses in the fireplace, which will increase the temperature.
One of the reasons is that a wooden stove heats a house better than a fireplace. So, I will answer the question, “What’s a wood stove baffle?
In A Wood Burning Stove, What Is A Baffle Plate?
In general, a baffle is a barrier that limits the flow to the intended outcome of a gas or liquid.
For example, there is a plate between the tank entrance and exhaust parts in a septic tank. Water can be flowing over it but not underneath the plate. That allows solid waste in the water to settle towards the bottom of the tank, preventing it from being blocked in the drainage field.
Similarly, so is the baffle plate in a wood stove. It’s commonly located between the fireplace and chimney, reducing the airflow from the top to the roof of the fireplace to a small space. Because combustion gases cannot easily escape, they are recirculated by the stove, further combustion is performed, and the fire temperature rises.
What Does A Wood Stove Baffle Do?
The objective of a wood burning stove is to:
- Stop waste gas and heat from being lost via the stove pipe too rapidly.
- Reflect the heat from the fire back in the firebox to help secondary waste gas combustion to generate even more heat.
- Prevent fire heat from harmful components, such as stove pipe, at the top of the stove.
How Does Baffle Plate Operate?
Our wood burning pipes and several fuel stoves are on top of the apartments. The baffle avoids leaving the firebox with hot air and waste gases, diverting them through a tiny space at the top of the kitchen.
Otherwise, the stoves cannot create as much heat without a baffle plate because all the heated air would quickly flow. Heat is also not reflected above flames to help secondary gas combustion.
Typically, baffles are directed to the front of the fireplace. Due to the intense heat of flames, baffle plates are usually formed of a thick metal plate.
Baffles can be taken from wood burning and multiple furnace stoves because, with time, they are damaged by warping and splitting. A mess can disturb a stove’s efficiency and must be changed to return the stove to its full functioning.
The stove may survive a long period, as long as it is properly managed and maintained. This implies that fires are kept for your particular stove type within the prescribed temperature range.
Without The Baffle Plate, Is It Safe To Operate A Wood Burner?
The answer to the question might indeed be summarized in a somewhat safe but exceedingly unwise manner.
There is hardly any danger to the users when a wood burner operates without a baffle. However, your stove may get irreparably damaged because it cannot defend against excessive heat.
Concerning the expense of replacing a twisted or damaged stove, a tangled or broken baffle may be substituted quite cheaply.
If you operate a wood burner without baffle, more of your fuel’s flame retardant gasses will immediately disappear up the chimney without being consumed. It is terrible for the environment and terrible for your pockets. (You are paying for fuel that may heat your house but will not be burnt in the sky) This is not enough to burn the combustible ones as well as for your unused fuel.
How To Remove Wood Stove Baffle
- To locate the baffle plate at the top of the heater, open the door or doors of the wood heater.
- Push up the plate’s front edge.
- Put a rubber mail on the underside of the trunk to free the jammed platform. Then, after extensive durations of fire cooling and heating, the baffle might be securely trapped in the rear.
- Spray lubricant on the heater wall with the bolts supporting the blanket. Leave the lubricant for at least 10 minutes.
- Loosen a slotted screwdriver’s head from the bolt. Switch to pinion and grip bolt heads if it is not easy to remove them from the screwdriver.
- Remove the plate from the heater by lifting it up and out of the interior of the rear wall.
How do I clean a wood stove baffle?
Remove the waste from the ash pan within the box (bottom of the box). Next, clean your baffle with a brush or shop vacuum (the top or ceiling of your wood stove) and carefully put your baffles in the correct place.
What is the material of a wood stove baffle?
According to The Stoves Yard, some of the usual baffle materials are cast iron, heavy steel, stainless steel, and vermiculite. The fog is built of fire brick in some bigger stoves.
How can I replace the wood stove baffle?
Check out this video for detailed instruction:
To wrap up, a wood stove baffle is the deflector shield that reflects heat into the combustion chamber, situated on the top of the fire chamber. This guarantees that the heat is kept in the stove and discharged into the room in a regulated way. Under any circumstances, you should keep it clean and well working!